/ / Plump Tufted Pillows Tutorial featuring Cuddle fabric

Plump Tufted Pillows Tutorial featuring Cuddle fabric

|


cover.jpg

Okay, I had a really hard time naming this tutorial because it’s for two things, really.

You can sew these really awesome plump tufted pillows with fringe all around the edges… and then you can pile them up (with the star I showed you how to make here) and make an adorable Christmas Tree! 

So my other name for this tutorial was ‘The Pillow Pile Christmas Tree.’ I can’t decide which I like better.


tree.jpg

how to make my Plump Tufted Pillows: 

You’ll need to start by picking your pillow sizes and sewing round pillow forms in those sizes. See my ‘Cutting Big Circles‘ tutorial to make it easy. 


DSC_0919.JPG

Next gather your pillow cover supplies.  I used plush Cuddle 3 from Shannon Fabrics, 1 7/8” covered button kits (they can get pricey, but I got a set of 12 {here} for $10), and Simplicity Pompom fringe trim from Joanns. On my other pillows I used vintage fringe trims that I bought from various sources on Etsy.

You’ll also need strong thread and long doll needles for the hand sewing part. 

Here’s a little chart to tell you how much fabric and trim to cut for each pillow: 


Fullscreen capture 11122013 121949 AM.jpg

Obviously, if you are using fabric that is less than 60” wide you will need to buy more fabric and piece together some of your rectangle strips. 

FYI: my Pillow Pile Christmas Tree is made with pillows that are 10”, 12”, 14”, 16”, and 18” in diameter and my Cuddle star

Lay the trim along one long edge of a fabric rectangle, with the decorative part (pompoms or fringe) facing inward. Baste the trim to the fabric right side.

Lay your second fabric rectangle on your workspace right side up and place the rectangle with the trim over it, right side down. Pin all along the edge, sandwiching the trim inside. Sew with a 1/2” seam allowance. If your trim is bulky like these pompoms, you might use your zipper foot like I did. 


DSC_0939.JPG

Look  how cute that turns out! 

Match up the two short ends and pin, right sides facing. Sew together, going slowly over the trim, to make a big circle of fabric.

Now for some easy hand sewing. Thread a needle with a double length of thread and knot the end. Secure your thread in one spot (I like to start at the seam) and sew with long stitches all the way around one edge of your circle. 

This is just like sewing a yo-yo.  Gather the fabric along your thread as you sew all around the edge. When you get to the place where you started, pull the thread tight and secure it. Remember, the bigger your stitches, the smaller your hole will be. As long as your hole is smaller than your button, you’ll be fine.

Insert your pillow form and repeat the sewing process on the other side. This time is a bit tricker because the pillow form is inside. Be careful pulling the thread tight because if it breaks, you’ll have to start over. It really helps to use strong thread. 

My covered button kits didn’t come with instructions, but it’s very easy to assemble them. Just cut fabric circles a bit larger than the buttons, wrap and stretch the fabric over the smooth side, catching it in the teeth on the inside, and then snap on the back.  No problem.


DSC_0981.JPG

For the tufting part (sewing on the buttons) I totally recommend these doll needles. You can attempt it without them, but you will probably make yourself swear and maybe even bleed. Just a warning. 

Thread it with a double length of your strongest thread. The color doesn’t really matter. 

After much practice, here is my best method for sewing on the buttons: 

1. Insert the needle through the hole on one side (let’s call it the front) an out through the hole on the other side (the back). 

2. Don’t pull your thread all the way through, leave about a 6-8” tail on the side we called the front.

3. Sew through the button eye, and then go back through the pillow to the front. 

4. Using that 6-8” tail that you left, tie a sturdy knot, pulling as tight as you can without breaking your therad. One button on!

5. Now sew through the other button eye… 

6. Go back through the pillow to the back and through the first button eye again for extra strength… 

7. Sew through the pillow one last time to the front and tie a knot again using that tail of thread. If it’s a big pillow, you might have to use your knee to squish it down to get that thread nice and tight.


DSC_1006.JPG

All done! 


DSC_0131_01.JPG

Now go make a big pile because it’s just so easy. You might also love my Patchwork Bench Cushion Tutorial – it also has buttons!

Happy sewing! 

Sharing is Caring!

Disclosure: some of my posts contain affiliate links. If you purchase something through one of those links I may receive a small commission, so thank you for supporting SewCanShe when you shop! All of the opinions are my own and I only suggest products that I actually use. 🙂

Similar Posts

6 Comments

  1. Hermoso trabajado..saludos desde CHILE¡¡¡

  2. Hermoso trabajado..saludos desde CHILE¡¡¡

  3. Lisa Gardner says:

    I love Craftsy too, I have numerous courses there! I just signed up for your emails, am so enjoying the tutorials! Thanks for all your hard work! I plan to try these cushions for some gifts!

  4. I love how easy this looks to make the way you have explained it! Wonderful gift idea for my grand-daughters! Thank you sew much!
    God bless!

  5. Oh man . . . I could have used your tufted button trick a couple weeks ago!! I could not get a tight tuft the way I did it on a pillow I recently made. I’m keeping your trick in mind. Thank you!

Leave a Reply

Your email address will not be published. Required fields are marked *